Wednesday 2 March 2016

Taming the sketch point selections when adding a hole.


In the above picture I have used only 1 sketch for the locations of the slots and the hole. I created the Cut feature for the slot first and then shared the sketch so that I could add a Hole feature.

I hit a snag when I started the Hole feature in that both of the Sketch points were chosen and I couldn't un-select the point in the middle of the slot. I tried Shift and click and Ctrl and click, nothing worked.

The solution was to exit the Hole feature, select the 1 Sketch point first and then start the Hole feature again. This limited the Centres to only the 1 I had chosen and I was able to complete the Hole feature.

Below is a quick video of the process, and me stuffing the Hole direction up which I promptly fixed. No comments needed on that, we are all human (just some more human than others).



Tuesday 23 February 2016

Redefining middle plane of Content Centre parts.


While writing this post I realised that it's practically 1 year to the day since my last post! Seems like only last month. Time sure flies.

Anyway, onto the topic of this post. The title is really referring to Structural Steel members placed from the Content Centre (CC). Each family, even those supplied by Autodesk, appears to be an extrusion from the Start Plane out 1 direction, therefore making a midpoint Flush/Flush constraint difficult because you need to do some calculations (1/2 the member length) to get it constrained mid-plane into your assembly. For reasons I won't go deeply into now, I place all CC members as Custom. I do this is mainly because the file becomes somewhat editable and I can change the extrusion to get the mid-plane where I want it, in the middle.

Friday 20 February 2015

Tip for Sketch Pattern and Suppress elements


Work is biting into my post schedule so this is just a quickie that I discovered myself just today. The context is that I want to pattern the 2 diam 14 holes at the top (12 o'clock) 3 times meaning that I will have a set at 3 and 9 o'clock. Because I started at 12 I can't get that pattern without doing it 4 times in 360 degrees and then RMB on the 2 holes I don't want and Suppressing them.

My discovery today is the double arrow in the bottom right corner of the Pattern window. Expanding it shows a Suppress button and if I hit that and select either of the 2 unwanted holes the command will Suppress those while inside the Pattern command. A real time saver which in my books is a bonus!


Below is a video of the process. Note that this is in 2014 so I expect it to also be in newer versions, but whether in older I don't know.






Thursday 5 February 2015

Fun with PDF file sizes

I greet you with a short post due to work commitments. The post is about the variety of PDF file sizes I get with the 3 programs I use. This is something I've noticed for a while and it's become more critical since I upgraded to mobile broadband (from dialup - yuck) and I now have a strict quota with big $ overtime charges. Why I'm on mobile broadband is a long story which I won't go into, except to say that landline broadband isn't available at my bush block 'little patch of heaven'.

My PDF writer of choice has always been CutePDF due to it's small size, easy configuration, great output and community support. It is just a great and simple tool to pump out a quick PDF. Next was PDFCreator which is no where near as simple to use or configure, and conversely is powerful in it;s batch ability and many other attributes which I often use. Finally, and only if I had too, I would revert to Inventors built in PDF Export which feels clunky like Inventors Print Dialogue, and for this reason I didn't use it.

The picture below shows the various file sizes created by each of the programs. I have to admit that I'm surprised by Inventors Export PDF file size which is the smallest by a long way at 462 KB.

I did a few tests with CutePDF, trying to see if I could get better results and I could only get the file size down to 2.41 MB which is only a small decrease from the default settings which produced a 2.64 MB file. A quick Google search showed my how to change the dPDFSETTINGS value in the config file and I tried each of the options that should create a smaller file, but I experienced only a small change.

PDFCreator had a better output than CutePDF but still a long way short of Inventors output. PDFCreator produced a 1.76 MB file with a bit of tinkering.

The same Inventor IDW file was used for each of the tests, and each PDF printer was set at 150 odd DPI and full colour and A3 size. There was no noticeable difference in any of the PDF files.


So, with some humble pie swallowed I'll have to start using Inventors Export PDF a bit more. I just need to find a way of locking in the DPI at 150 because it annoyingly keeps changing back to 400 DPI which will again blow the file size out, and from a Print Range of All Sheets to Current Sheet which is just a royal PITA, and to stop the PDF from automatically opening. Not asking for too much, hey?


Now, if I could just find a person smarter than me (shouldn't be hard) to write me some iLogic to run the Inventor Export PDF with All Sheets on and 150 dpi I'd be as happy as a slinky on an escalator :)

Monday 26 January 2015

Sharing your custom Content Centre Library

This week I've taken on some home based design/drafting for my day job employer. Getting the templates is easy as is the Design Data, but 1 thing I struggled with was the custom Content Centre (CC). At my day job I have heavily customised the CC to suit our requirements. I have added a lot of content based on custom rolled profiles we make and to make up for the basic amount of Australian Standard (AS) data that comes with Inventor. Through my day job VAR I found that the good folk at Autodesk made a method to allow me to export this custom CC and to bring that into my home Inventor so that I can work with the custom CC data and expanded AS families. In this posting I'll only be showing how to get a Vault CC Library exported for Desktop Content, but the reverse is also possible through the same set of dialogue boxes.